Mossy Hopper SBS

Discussion in 'Fly Tying Step by Step / Video' started by ScottP, Nov 22, 2013.

  1. ScottP Active Member

    Posts: 632
    Ratings: +878 / 0
    [IMG]

    First saw this tied up by Bob Kramer when he ran his shop in Bridgewater, VA just down the road from Mossy Creek (hence the fly's name). Despite the fact I've never seen too many ground hogs swimming in the stream, the materials provided by the unfortunate critter (plus a little hackle), seem to keep it on top of the water pretty well. A good fly for little streams, cast it at a distance and it's a bit of a b.tch to see. A nice example of a fly that takes about as long to tie as it does to lose it.


    hook - Dai Riki 320 #12
    thread - Danville 6/0 brown
    tails - woodchuck guard hair
    body - woodchuck underfur
    wing - woodchuck guard hair
    hackle - brown/grizzly


    mash barb, attach the thread and wrap back to point above barb

    [IMG]


    cut a clump of woodchuck guard hairs, comb out underfur (save for the body)

    [IMG]

    [IMG]


    measure tail for length (hook gap) and tie in; brush a little Super Glue on the wraps to keep it from torquing (optional)

    [IMG]

    [IMG]


    mix up the underfur; I just pulled it apart a few times to get a rough mix

    [IMG]


    spin bobbin to unwind thread and split; insert dubbing and spin bobbin to capture dubbing (don't make it too tight)

    [IMG]

    [IMG]

    [IMG]


    wrap body; pick it out (I used velcro'd popsickle stick) if you want it a bit shaggy

    [IMG]


    clean, stack another clump of guard hairs (keep the underfur for the next fly); let the tips extend even with the tail

    [IMG]


    tie down wing and apply a few posting wraps at the front to tilt the butts up a bit

    [IMG]


    tie in hackles; wrap forward, tie down, half hitch x 2 and SHHAN

    [IMG]

    [IMG]


    trim wing butts a little past the hook eye; go fishing

    [IMG]



    trim hackle flat on bottom for lowrider effect (optional)

    [IMG]


    Regards,
    Scott
  2. Richard Olmstead BigDog

    Posts: 2,494
    Seattle, WA
    Ratings: +791 / 0
    We don't see woodchuck fur in fly shops here in Washington much. Do you know a good source on the internet?

    D
  3. ScottP Active Member

    Posts: 632
    Ratings: +878 / 0
    Richard,

    A quick search on my Google machine came up with this

    http://www.flytyingfurs.com/products.htm

    Never dealt with these folks but a whole ("damaged") skin for $4.50 (plus shipping) doesn't seem too bad; I'm sure others carry pieces. If you could get marmot, you'd probably get the same effect.
    Saw a number of them sunning themselves by the side of the road, with a few stiffies thrown in that apparently lacked sufficient fast-twitch muscles. Never really saw them as candidates for harvesting - if you ever saw Eric Leiser's Flytying Materials (and their procurement), you'd understand (ugh!).

    Regards,
    Scott
  4. flyfishmt Active Member

    Posts: 158
    Laurel, MT
    Ratings: +96 / 0
    Great looking step by step pictures. The end product looks great. That fly would work all over Montana.
  5. ScottP Active Member

    Posts: 632
    Ratings: +878 / 0
    Thanks. I'm pretty this fly's been around in one form or other for a while - if I remember correctly, Chuck Stranhan, who runs a flyshop in Hamilton on the Bitterroot, came up with something similar.

    Regards,
    Scott