Step by Step - Avalon Fly for Permit - Saltwater

Discussion in 'Fly Tying Step by Step' started by TomFishermen, Nov 21, 2011.

  1. TomFishermen

    TomFishermen New Member

    Joined:
    Nov 14, 2011
    Messages:
    2
    Likes Received:
    0
    Location:
    Miami , Florida
    STEP 1

    Insert the hook into the vise, and set up thread onto the hook shank.

    [​IMG]





    STEP 2

    Tie in the dumbbell eyes on top of the shank, about 1/5 of the way back from the eye of the hook. Place the eyes against your thread base, perpendicular to the hook shank. Do a diagonal wrap across the top of the eyes and down the other side in front of the eyes. Take the thread under the shank behind the eyes and back to your original start location. Start now making figure eight, 8 wraps and don’t be shy with tying thread. To finish the job, add a drop of super glue. This will insure that the eyes will stay in place even after you have caught a fish. When the eyes are secured and the super glue dried, tie in an eight centimeter piece of clear hard (stiff) 20 lb monofilament . To finish this second step, tie in a small bunch of arctic fox approximately 3,cm long. After the fibers are well secured, shorten the tips until about 1 cm is left. Check your result compared to the picture.

    [​IMG]





    STEP 3

    Select two Krystal flash fibers and tie them in on the left and right side of the hook shank. Best way is do it one by one! Cut the off at a length of 7 cm.

    [​IMG]





    STEP 4

    First tie in the two rubber legs one by one. One on the left side of the hook shank, the other one on the right side. Be sure they are positioned symmetrically, which is very important for the action and mobility of the fly. Cut them off at about a length of 5 cm. Now take two strands Pearl Diamond Braid and do exactly the same trick as for the rubber legs, but cut them both at 4 cm length.

    [​IMG]

    [​IMG]





    STEP 5

    Now tie in the marabou at the tip.

    [​IMG]





    STEP 6

    Wrap the marabou feather, under some good pressure, forward and secure it with your tying thread.
    Cut off the surplus.

    [​IMG]





    STEP 7

    Tie in the zonker strips one by one. Start from the hook eye and secure the strips well, all the way from hook eye until just behind the dumbbell eyes . Be sure the inside of the zonker skins are facing to the body to the right and left side as shown clearly in the picture. To create the delta wing shape, give extra tension on the last few windings of your thread. If the shape does not turn out nicely, wrap your thread around the strip and pull the strip into the required shape. The claws should be positioned at an angle of 45 degrees with the body of the fly!

    [​IMG]





    STEP 8

    Now take the right piece of Pearl Diamond Braid and pull it over the body to the left side of the hook eye and secure. Pull the left Braid over the body to the right size of the hook eye and then secure both with your thread.

    [​IMG]





    STEP 9

    Take your four silver beads and add them on your monofilament, then pull the monifil forward and until your keel has a loop 2 cm long and 1 cm deep or wide. Then secure the monofilament at the eye on top of the hook shank as shown in the pictures and tie off by whip finisher. Then set up your orange thread and make a nice orange head

    [​IMG]





    STEP 9A & 9B

    Then secure the monofilament at the eye on top of the hook shank as shown in the pictures and tie off by whip finisher. Set up your orange thread and make a nice orange head

    [​IMG]

    [​IMG]

    The video on YouTube:
     

Share This Page