Ideas for Pontoon boat rod holders

Discussion in 'Watercraft' started by SeanM, Oct 29, 2008.

  1. SeanM

    SeanM member

    Joined:
    May 14, 2007
    Messages:
    158
    Likes Received:
    4
    Location:
    Seattle, Wa
    I'm looking for an affordable - possible home-made solution - for a pontoon boat rod holder.

    I know that scotty makes some nice ones, but honestly I'm not looking for anything fancy. Just something to hold my spare rod while I'm out fishing, but without the rod being in the way while casting or landing a fish.

    Any of you out there come up with some easy-to-build or cheap solutions?



    Sean
     
  2. Couleeflyfisher

    Couleeflyfisher Member

    Joined:
    Oct 4, 2001
    Messages:
    398
    Likes Received:
    4
    Location:
    .
    You can make a nice one out of a short length of pvc, either fasten it to side of seat , if you have a hard seat, or attach to rack in back. I have both, just cut a
    3/4 inch slot 4" or so down side of 8" to 12" piece of pvc. I have one on both sides of my seat and another I can bunge to rear rack.
     
  3. Mike (Doc) LaCombe

    Mike (Doc) LaCombe Member

    Joined:
    Jul 15, 2007
    Messages:
    417
    Likes Received:
    10
    Location:
    Port Orchard, WA
    I am also looking for a way to attach my 2nd rod to my pontoon boat. I have a scotty holder which works great when trolling. I need some way to hold the rods down along side the tubes while using the other. I am a visual person so pictures of what others are using would be helpful.

    Thanks

    Mike
     
  4. Jay Burman

    Jay Burman Fly Fisher, Bon Vivant, Layabout.

    Joined:
    Nov 27, 2003
    Messages:
    377
    Likes Received:
    81
    Location:
    Snoqualmie, WA, USA.
    The easiest, best and least expensive solution is to go with the Scottys. I use 3 on my pontoon boat. Two for holding the rods securly while I'm transporting and one mounted in the front so I can row and troll if it gets windy. They're not expensive and they are very adjustable allowing numerous angles and positions. I'm really pleased with the quality and value.:thumb::thumb:
     
  5. speyfisher

    speyfisher Active Member

    Joined:
    Jan 16, 2006
    Messages:
    1,339
    Likes Received:
    364
    Location:
    State of Jefferson U.S.A.
    If they are just single hand rods, no longer that the pontoons, just bungie cord them to the farme. Layed flat olong the top of the pontoon. Spey rods are another story.
     
  6. Ed Call

    Ed Call Mumbling Moderator Staff Member

    Joined:
    Jun 9, 2008
    Messages:
    19,620
    Likes Received:
    4,624
    Location:
    Kitsap Peninsula
    If you don't want your bungies around the rods, get a cheap clip in rod rack at your local wal mart or sporting goods place. Bungie that around your toon, clip your rod in and presto, you are in business. Out of the way for casting, rowing, fighting fish and still at your side for quick deployment when needed. I have large diameter long locking PVC tubes that I can attach to my frame that will hold my rods (in two piece mode) so that I can leave them locked up while returning to my rig. That is overkill for your described need, I'd go with a simple plastic and foam rod rack. If you want real minimal get a large diameter pool noodle and cut two pieces, one fore for the butt section and one aft to hold the tip section. Bungie in place and you are out about $5.
     
  7. Mike (Doc) LaCombe

    Mike (Doc) LaCombe Member

    Joined:
    Jul 15, 2007
    Messages:
    417
    Likes Received:
    10
    Location:
    Port Orchard, WA
    Pictures guys. I need pictures.

    Mike
     
  8. Gatorator

    Gatorator Member

    Joined:
    Mar 5, 2008
    Messages:
    277
    Likes Received:
    1
    Location:
    Pend Oreille Valley, Idaho
    I just bought a rod case with attached reel cover at SPORTCO. About $10.00 on sale I think. You can put two rods, taken down but still strung with flies, into it and zip the thing shut. Bungy to the pontoon boat and you are good to go.

    Especially good if you are on a river with any fun spots to navigate. :cool:
     
  9. Jefffly

    Jefffly The more we know, the less we can learn!

    Joined:
    Feb 19, 2008
    Messages:
    103
    Likes Received:
    0
    Location:
    sequim, wa
    I use 1" pvc pipe and two straps with clips on them used my rotozip to cut slot down pvc to slide reel into and simply strap them to the front of my toon so the rod tips are basically even with the back of my toon I can easily adjust the angle to have the rod lay almost flat or have the tips up in the air a bit. they are always out of the way and easy to access id show you a pic but its raining like crazy outside and my toon is hanging from the ceiling and I really dont want to go out and take a pic. maybe in a few days when it stops raining and I take the toon floating again.
     
  10. Jefffly

    Jefffly The more we know, the less we can learn!

    Joined:
    Feb 19, 2008
    Messages:
    103
    Likes Received:
    0
    Location:
    sequim, wa
    hope this helps I decided to get oof my lazy arse and just go take some pics it also shows my hoist for storage quite nicely! pontoon 001.jpg

    pontoon 002.jpg

    pontoon 003.jpg

    pontoon 004.jpg
     
  11. Mike (Doc) LaCombe

    Mike (Doc) LaCombe Member

    Joined:
    Jul 15, 2007
    Messages:
    417
    Likes Received:
    10
    Location:
    Port Orchard, WA
    Thanks Jeff for the pics. I was thinking along those ideas so now I see what I have to do.

    Mike
     
  12. Cast2way

    Cast2way row-ho services for hire

    Joined:
    Aug 13, 2008
    Messages:
    58
    Likes Received:
    0
    Location:
    Boise, ID
    Depending what type of 'toon you have, you might consider new side pockets like those from North Fork Outdoors (.com). They have a mesh pocket along the side with 2 velcro straps and to store a rod, you just insert the reel and butt end into the pocket and secure with the velcro. The rod tip ends up sticking our the back of the boat so you have to be cognizant of that when backing into the bank or around trees. I can't find a picture to show so let me know if you want one to better understand and I'll see if I can take a quick 'un.

    Another solution is to just strap a 1-1/2" PVC pipe along the outside of the frame under the straps like the pic below. This way the entire rod is protected and a neoprene reel case protects the reel. This boat has 13' pontoons so you would have to take that into consideration:

    [​IMG]

    The rod is held in with a rubber snubber replacement you can get for ATV gun racks:

    [​IMG]

    Mike T
     
  13. Ed Call

    Ed Call Mumbling Moderator Staff Member

    Joined:
    Jun 9, 2008
    Messages:
    19,620
    Likes Received:
    4,624
    Location:
    Kitsap Peninsula
    Mike T that is a nifty setup.
     
  14. Gatorator

    Gatorator Member

    Joined:
    Mar 5, 2008
    Messages:
    277
    Likes Received:
    1
    Location:
    Pend Oreille Valley, Idaho
    castaway

    How do you get that rod out when you are on the river.
     
  15. Richard E

    Richard E Active Member

    Joined:
    Oct 5, 2001
    Messages:
    4,643
    Likes Received:
    211
    Location:
    Seattle, WA, USA.
    This is the way to go. I do it all the time. I use a double reel-on rod case and store the rigged-ready-to-go unused rod(s) in the case. A simple bungee or velcro strap arrangement works fine to hold the case.

    When I want to change sticks/lines/flies, I swap the rod being used for one in the case. Because the rods are 'broken down' in to two pieces, they are easy to move/remove from the case while a person is out on the water. And, because they are already rigged (i.e. line through the guides, etc.), it's easy to get the stored rod back in to action. Not to diss Mike T's design, but full rod length storage like his, especially when it's on the side of the tube away from the rower and fisherperson, would be pretty tough to remove a rod from the rod tube while the raft is underway.