Wings

Discussion in 'Fly Tying' started by Jerry Knudson, Apr 2, 2009.

  1. Jerry Knudson

    Jerry Knudson New Member

    Joined:
    Mar 20, 2009
    Messages:
    48
    Likes Received:
    0
    Location:
    Lakewood, Wa or AZ
    I am new to tying and have found that in a few short months it has become an obsession
    Now I am faced with the near daily dilemma of having a fly I want to tie and not having the material I want:( Of course this means another trip to the local shop. I have recently though come up against not having a good material for making Crane Fly wings. I am looking for suggestions on what I could use. I don't like how the clear plastic wing material looks or acts, and have tried web-wing material with better but unsatisfactory sucess.
    Any suggestions?
     
  2. Connor Parrish

    Connor Parrish Member

    Joined:
    Nov 23, 2007
    Messages:
    268
    Likes Received:
    2
    Location:
    Covington, Wa
    the thin white strips of packing foam. it isn't very durable, infact it falls apart after like 3 fish. but i have used it on caddis patterns and it works very well. i wish i could find something that looked as good and was more durable. try it tho
     
  3. Preston

    Preston Active Member

    Joined:
    Mar 12, 2004
    Messages:
    2,817
    Likes Received:
    925
    Location:
    .
    Tiers from Great Britain and Ireland have created a wide variety of patterns to imitate the crane fly. They are usually referred to as Daddy Long Legs or just "Daddies". All the ones I've seen use hackle tips for wings.
     
  4. Jeff Dodd

    Jeff Dodd Active Member

    Joined:
    Dec 4, 2004
    Messages:
    1,871
    Likes Received:
    630
    Location:
    Langley, WA
    The pattern I learned calls for bleached coastal deer hair.

    The pattern uses embroidery thread for the body and then this same material splits the deer hair you tie in to create the wings.

    This is Gordon Swanson's crane fly pattern

    Jeff
     
  5. Jerry Knudson

    Jerry Knudson New Member

    Joined:
    Mar 20, 2009
    Messages:
    48
    Likes Received:
    0
    Location:
    Lakewood, Wa or AZ
    Thanks all for your input I really appreciate it. Going to try them all and see what I come up with....
     
  6. Calvin1

    Calvin1 Member

    Joined:
    Feb 26, 2003
    Messages:
    629
    Likes Received:
    21
    Location:
    Seattle, WA
    I'll second, third or fourth the vote for hackle tip wings for the crane fly pattern. My question is what type of body and legs are you using?
     
  7. Richard Torres

    Richard Torres Active Member

    Joined:
    Jan 16, 2003
    Messages:
    1,412
    Likes Received:
    92
    Brown Raffene (Swiss Straw) makes good wings.
     
  8. Jerry Knudson

    Jerry Knudson New Member

    Joined:
    Mar 20, 2009
    Messages:
    48
    Likes Received:
    0
    Location:
    Lakewood, Wa or AZ
    Sorry for the response delay, have been unable to log on latley. Calvin1, to answer your question I have tried both a thread body, and a lightly dubbed body with fair results on both. Use and extended body jig and wrap over a few strands of plastic fibers like paint brush fibers with a touch of glue on the thread to start to keep it where I want. Results have been fair so far except for the wings, Legs have been pheasant tail fibers knotted on one bent with heat on another.
    I have found just a small piece of clear/rainbow raffia that makes the best wings so far.

    Thanks for your responses.
     
  9. Preston

    Preston Active Member

    Joined:
    Mar 12, 2004
    Messages:
    2,817
    Likes Received:
    925
    Location:
    .
    I've planned for years to sit down and try to come up with a cranefly pattern and this thread finally got me moving. My old pal Dan Lemaich always favored a cranefly as a dry pattern for sea-run cutthroat in the rivers in the fall but I never bothered to ask him about his pattern. The pattern I came up with relies a bit more heavily on synthetics than I would like but I wanted something that looked pretty accurate. The abdomen is built with 3/0 thread wrapped on a mandrel (a needle in this case) and coated with Softex (the same technique I use for my extended-body Baetis pattern) and the legs are knotted paintbrush bristles. It's a bit time consuming but I quite like the results.
     
  10. Preston

    Preston Active Member

    Joined:
    Mar 12, 2004
    Messages:
    2,817
    Likes Received:
    925
    Location:
    .
    Here's the pic.
     
  11. Mark Walker

    Mark Walker Active Member

    Joined:
    Apr 27, 2008
    Messages:
    2,855
    Likes Received:
    333
    Location:
    So. Cal.
    Excellent tie.